On the Post-cure Case (UV Inks)
June 2001
|
Industry experts weigh in on the who, what, when, where, and why of the post-cure process.
by Jessica Millward, Associate Editor
THE APPARENT "chemistry mystery" occurring after a UV ink is cured significantly impacts the appearance of a finished printed product. Supplier sleuthing has led to these conclusions:
WHAT is (and what isn't) post-cure?
Though used throughout the industry, the term "post-cure," in many cases, is technically a misnomer. Rob Stendahl, corporate technical support supervisor for Akzo Nobel, clarifies: "Post cure only takes place with cationic UV-curable inks. The more common type of UV inks is cured through a UV-induced free radical polymerization process and has no post cure at all. What many people refer to as post cure is simply the relaxation of the high level of stresses built up into the ink film during the materials' incredibly fast cure process."
Sun Chemical Energy Curable Inks Market Manager Tony Bean concurs, explaining, "…[F]or free radical polymerization, the free radicals are consumed very quickly or quenched once they are generated." Once the ink lacks exposure to UV light, the free radicals deplete and curing ends.
WHEN is the cured ink "done"?
At Flint Ink, they refer to the "relaxation" period of typical UV inks as "post change," and estimate it as lasting approximately one day. Technical Manager, Radiation Cure, Rod Balmer asserts, "The amount of post-change will decrease with time at an exponential rate. Most of the change is likely to occur within the first few hours. At 24 hours after exposure we would expect to see little or no change."
Though post-cure or post-change can't be measured precisely, printers should focus on the printed results—and if they meet end-user standards by the end of the run. Kurt Hudson, UV products general manager at Water Ink Technologies, believes printers ought to concentrate on whether the ink is cured well enough at the end of the line to either pass all requirements of the end-use environment, or if it will pass a test predicting its eventual conformance to those requirements.
WHO determines successful UV ink curing?
Long before ink meets lamp, the effectiveness of a UV cure is set on course by the ink formulator. First, the change in finished substrate properties after curing is heavily influenced by the additives contained in the ink. Bean maintains, "Slip additives such as waxes and silicones, flow agents, and other materials can slowly or quickly come to the surface of the film and impact the performance of the ink."
by Jessica Millward, Associate Editor
THE APPARENT "chemistry mystery" occurring after a UV ink is cured significantly impacts the appearance of a finished printed product. Supplier sleuthing has led to these conclusions:
WHAT is (and what isn't) post-cure?
Though used throughout the industry, the term "post-cure," in many cases, is technically a misnomer. Rob Stendahl, corporate technical support supervisor for Akzo Nobel, clarifies: "Post cure only takes place with cationic UV-curable inks. The more common type of UV inks is cured through a UV-induced free radical polymerization process and has no post cure at all. What many people refer to as post cure is simply the relaxation of the high level of stresses built up into the ink film during the materials' incredibly fast cure process."
Sun Chemical Energy Curable Inks Market Manager Tony Bean concurs, explaining, "…[F]or free radical polymerization, the free radicals are consumed very quickly or quenched once they are generated." Once the ink lacks exposure to UV light, the free radicals deplete and curing ends.
WHEN is the cured ink "done"?
At Flint Ink, they refer to the "relaxation" period of typical UV inks as "post change," and estimate it as lasting approximately one day. Technical Manager, Radiation Cure, Rod Balmer asserts, "The amount of post-change will decrease with time at an exponential rate. Most of the change is likely to occur within the first few hours. At 24 hours after exposure we would expect to see little or no change."
Though post-cure or post-change can't be measured precisely, printers should focus on the printed results—and if they meet end-user standards by the end of the run. Kurt Hudson, UV products general manager at Water Ink Technologies, believes printers ought to concentrate on whether the ink is cured well enough at the end of the line to either pass all requirements of the end-use environment, or if it will pass a test predicting its eventual conformance to those requirements.
WHO determines successful UV ink curing?
Long before ink meets lamp, the effectiveness of a UV cure is set on course by the ink formulator. First, the change in finished substrate properties after curing is heavily influenced by the additives contained in the ink. Bean maintains, "Slip additives such as waxes and silicones, flow agents, and other materials can slowly or quickly come to the surface of the film and impact the performance of the ink."
Companies Mentioned:
 |
|
|
|
Chemistry for the Graphic Arts
What the Printer Should Know About Paper